Booking today · Houston arrival windows 9–12 · 1–4 · 4–7 Independent Electrolux specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 979-9150 Request a Service Visit
Error code · Dishwasher

Electrolux Dishwasher Code Er 01: Leak Detected Under the Tub

Er 01 on the Electrolux Wave-Touch and IQ-Touch built-in dishwashers, the EWDW6505G and EIDW6305G, means the leak detector has found water under the tub. These are older models that are still in many homes, and we…

High · stop use, call now
Request a Service Visit(713) 979-9150
Code
Er 01
Appliance
Dishwasher
Brand
Electrolux
Warranty
30-day workmanship

What Er 01 means

Er 01 on the Electrolux Wave-Touch and IQ-Touch built-in dishwashers, the EWDW6505G and EIDW6305G, means the leak detector has found water under the tub. These are older models that are still in many homes, and we repair them, and say plainly when a repair is not worth it. The dishwasher stops so a leak cannot run on, and the display shows Er 01.

Common causes of Er 01

  • Water in the base pan from a leaking hose or clamp
  • Door gasket or tub seal leak
  • Fill valve or pump seal weeping
  • Leak detector triggered by old moisture
✓ One safe check you can try

1. Switch the dishwasher off at its breaker and shut off the water supply under the sink. 2. Wipe up any water visible around the door and floor. 3. Do not run the dishwasher again until the leak is found. 4. Call us and tell us where you saw water.

! Why to stop there
  • The code says water is present but not where it came from, so we trace the leak from the base pan back to its source.
  • Dry-out can clear the code but not stop a leak, so we do not just reset it.
  • We tell you the price in writing, and say plainly if an older dishwasher is not worth repairing.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Dishwasher codes

PRESS STARTElectrolux Dishwasher Message PRESS START: Close the Door i80 / i81Electrolux Dishwasher Codes i80 and i81: Automatic Door Opener i90Electrolux Dishwasher Code i90: Control Memory or Display Data Error iB0Electrolux Dishwasher Code iB0: Sensor Calibration Not Finished iC0Electrolux Dishwasher Code iC0: Display Not Communicating iC1 / iC2Electrolux Dishwasher Codes iC1 and iC2: Internal Communication iC3Electrolux Dishwasher Code iC3: Power and Motor Boards Not Talking iD0 / iD1Electrolux Dishwasher Codes iD0 and iD1: Motor Speed Signal Missing
Er 01Er 01 questions
Is it safe to run the dishwasher again?

We suggest not. If water is leaking, it can damage the floor and cabinets, so shut off the water and breaker until we check. A leaking dishwasher can soak the floor and the cabinet base quickly, so turning off the water and the breaker until we have looked is the careful choice.

Could it be a false alarm?

It can be if old moisture is left in the base. We still check, because a small leak can be hard to see. Spilled water from loading or a past leak can leave the base pan damp, and we confirm whether the leak is active or old.

Do I need to remove the dishwasher?

Often we can find the leak by pulling it forward slightly. We explain what is needed before we start. Pulling the dishwasher forward a little usually gives us access to the base and the hoses, and we tell you what is needed before we start.

Book a visit

Still seeing Er 01?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 979-9150
☎ Call our office ▤ Request a Service Visit