Booking today · Houston arrival windows 9–12 · 1–4 · 4–7 Independent Electrolux specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 979-9150 Request a Service Visit
Error code · Dishwasher

Electrolux Dishwasher Code i51: Wash Pump Running on Its Own

On Electrolux built-in dishwashers with the ICON control, including the EI24CD35, EI24ID30, EI24ID50, EW24ID70 and EW24ID80, i51 means the wash motor was seen running when the control had not switched it on. The message refers to…

Medium · inspection needed
Request a Service Visit(713) 979-9150
Code
i51
Appliance
Dishwasher
Brand
Electrolux
Warranty
30-day workmanship

What i51 means

On Electrolux built-in dishwashers with the ICON control, including the EI24CD35, EI24ID30, EI24ID50, EW24ID70 and EW24ID80, i51 means the wash motor was seen running when the control had not switched it on. The message refers to an asynchronous wash motor, and the dishwasher also fills up to its level when it happens. You will usually see the code on the display along with a cycle that stops or never gets started properly.

Common causes of i51

  • Wash motor drive circuit on the control
  • Motor control board connection to the wash pump
  • Wiring between the control and the wash motor
✓ One safe check you can try

1. Press Cancel, open the door and look for standing water in the tub. 2. Make sure the dishwasher has power and the door latches firmly. 3. Close the door and start a short Rinse cycle. 4. If i51 comes back, write down when it appeared and call us. Do not run long cycles with the code showing.

! Why to stop there
  • The code says the pump moved without a command, but not whether the board or the motor wiring caused it, so we test both ends.
  • We watch the fill and the pump start during a cycle on site.
  • You approve a written price before we start, and the work carries a 30-day warranty.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Dishwasher codes

PRESS STARTElectrolux Dishwasher Message PRESS START: Close the Door i80 / i81Electrolux Dishwasher Codes i80 and i81: Automatic Door Opener i90Electrolux Dishwasher Code i90: Control Memory or Display Data Error iB0Electrolux Dishwasher Code iB0: Sensor Calibration Not Finished iC0Electrolux Dishwasher Code iC0: Display Not Communicating iC1 / iC2Electrolux Dishwasher Codes iC1 and iC2: Internal Communication iC3Electrolux Dishwasher Code iC3: Power and Motor Boards Not Talking iD0 / iD1Electrolux Dishwasher Codes iD0 and iD1: Motor Speed Signal Missing
i51i51 questions
Why does the dishwasher fill when i51 shows?

The control fills the tub up to its level while it deals with a pump that started by itself. That is a protective response, so some water in the bottom is normal.

Is i51 the same as a motor that will not start?

No. i51 is the opposite situation, a pump running when it should be off. A motor that will not start shows a different i5 code.

Can I keep using the dishwasher?

We suggest you stop. A pump that starts without a command can run dry or overfill, so have us check it before the next full load.

Book a visit

Still seeing i51?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 979-9150
☎ Call our office ▤ Request a Service Visit